%3Aquality(80)&w=3840&q=75)
%3Aquality(80)&w=3840&q=75)
%3Aquality(80)&w=3840&q=75)
%3Aquality(80)&w=3840&q=75)
%3Aquality(80)&w=3840&q=75)
F1625 CF
Shielded for the most demanding industrial cutting
The F1625 CF is a precision ply cutter for prepreg and dry fiber: carbon fiber, glass fiber, quartz fiber and aramid (Kevlar). Up to three Z-axis-controlled tangential modules and application-specific tooling keep cutting pressure and material distortion low across long nests. And for conductive dust created by dry carbon fiber, this special configuration is built to keep running in the workspace that dust creates.
Who it's for
Perfect for
Composites manufacturers cutting prepreg and dry fiber plies to shape, at production volume.
Production floors where conductive dust is a constant condition rather than an occasional incident.
Teams building ply kits, who want cutting, labeling, picking and kitting in one connected workflow.
Built for a composite production workflow
%3Aquality(75)&w=3840&q=75)
Tech specs
What's in your F1625 CF
F1625 CF
Working area
160 × 250 cm / 63 x 98 inch
Dimensions
247 × 333 × 110 cm / 97 x 130 x 43 inch
Material width
Up to 165 cm / 65 inch
Vacuum
2 × 1.3 kW (50 Hz) or 2 × 2 kW (60 Hz)
Vacuum zones
8 zones (4 columns × 2 rows)
Speed
Up to 1000 mm/s / 39 inch/sec
Acceleration
Up to 1 G
Compressed air
320 l/min / 11.3 cfm
Power requirements
3 × 400 V + N, 50 Hz, max 20 A
or 3 × 208 V + N, 60 Hz, max 30 A
or 3 × 230 V, 50 Hz, max 20 A
or 3 x 400 V + N, 60 Hz, max 20 A
Materials
Industrial materials that are made to be cut with an F1625 CF
Prepreg carbon fiber
Dry carbon fiber
Glass fiber
Quartz fiber
Aramid (Kevlar®)
Technical textiles
Gasket and seal materials
Your unique vantage points
Cuts the ply, not the fiber orientation
Low cutting pressure and application-specific tooling keep material distortion down, so the nested shape and the cut shape are the same shape.
Read more
Runs in the dust it makes
Three layers of protection, at enclosure level and at board level, so a conductive contamination risk does not become a production stoppage.
Read more
Kitting in parallel
The optional 2.5 m (8.2 ft) conveyor extension turns downstream space into a second work zone. Ply cutting and kit building happen at the same time, not one after the other.
Read more
One workflow, not four systems
Nesting, labeling, picking and kitting connected through GoConnect, with kitting information on monitors at the table.
Read more
Built to be serviced
Improved access shortens maintenance interventions and simplifies everything from routine service to component replacement.
Read more
Three layers of protection
With conformal polymer coating on every PCB, cabinet pressurization and shielded interfaces for every exposed connector, your flatbed is protected for the most demanding working environments.
Read more
F Series
Other models in the F Series
F1612 Vantage
Working area
160 × 120 cm / 63 x 47 inch
Dimensions
247 × 220 × 110 cm / 97 x 87 x 43 inch
Material width
Up to 165 cm / 65 inch
Vacuum
1.3 kW (50 Hz) / 1.75 kW (60 Hz)
F1625 Vantage
Working area
160 × 250 cm / 63 x 98 inch
Dimensions
247 × 333 × 110 cm / 97 x 130 x 43 inch
Material width
Up to 165 cm / 65 inch
Vacuum
2 × 1.3 kW (50 Hz) or 2 × 2 kW (60 Hz)
F1832
Working area
184 × 320 cm / 74.4 x 126 inch
Dimensions
279 × 422 × 122 cm / 110 x 166 x 48 inch
Material width
Up to 190 cm / 75 inch
Vacuum
2 × 2.2 kW (50 Hz) or 2 × 2.55 kW (60 Hz)
F3220
Working area
327 × 210 cm / 129 x 83 inch
Dimensions
422 × 313 × 122 cm / 166 x 123 x 48 inch
Material width
Up to 332 cm / 130.7 inch
Vacuum
2 × 2.2 kW (50 Hz) or 2 × 2.55 kW (60 Hz)
F3232
Working area
327 × 320 cm / 129 x 126 inch
Dimensions
422 × 422 × 122 cm / 166 x 166 x 48 inch
Material width
Up to 332 cm / 130.7 inch
Vacuum
2 × 2.2 kW (50 Hz) or 2 × 2.55 kW (60 Hz)