Summa GoProduce Laser Edition - Version 2.2.1
Released: December 8, 2023
Changes to 2.2.1
Improvements
- Fixed size: better angle calculation for shapes where the height is different from the width.
- Fixed size (smart compensation): cut shapes are now only aligned in the X direction so the cut is more evenly distributed on the left and right of long shapes.
Fixed Issues
- Solved: issue in interpretation of Vision Camera calibration causing the cut to shift after a feed.
- Solved: "Invalid number of barcode characters" can occur in some cases when reading barcode with the vision camera.
Summa GoProduce Laser Edition - Version 2.2.0
Released: September 9, 2023
Changes to 2.2.0
New Features
- "Backup logging" functionality in "General" ribbon tab for troubleshooting.
- Added Korean language and translations.
Improvements
- Doesn’t allow to confirm device configuration if serial number is absent or invalid (unless it is a plot to file device), and shows info message "Invalid device serial number!".
- Now checks the minimum rom revision at device configuration. Shows info message "GoProduce LE requires at least firmware revision XX" if not high enough.
- Changed minimum rom revision to 3007 for L3214 and to 8 for L1810gen2.
- Logging of images when reading barcode if "LogLevel" application setting is set high enough.
- Faster timeout on mark recognition with the vision camera.
- Show proper error message when an user tries to import a material manager using the "import" button instead of using the "restore" function.
- Slightly increased width of virtual camera window for vision so that there's the same amount of margin for mark detection in both directions.
- More intelligent calculation of which marks to read to accurately do a prefeed.
- Fixed size compensation: improved center calculation for segmented shapes.
- Marks necessary to calculate prefeed are now sorted "by main direction (vertical)" instead of "by nearest object", resulting in better mark prediction in some cases.
- Fixed size compensation: improved center of shape calculation for shapes with noticeable difference in deformation at opposite sides of the shape.
- Optional property to "Crop to page size" when importing PDF files where figure is outside of the MediaBox to only import the visible part.
- The possibility to request to enter a job name on the "Load material" action which will be used in the "Joblog" if no job name is available, for example when using the "Trace" action.
- Uses slightly smaller region when searching the barcode line with the camera for stability.
- Added hidden contrast setting to barcode profile to cope with white space being detected as barcode line.
- Job time logging and job identification for Trace&Cut.
- Output option to omit waste cut on first segment.
Fixed Issues
- Solved: "Rendering" option under "General" tab is no longer working correctly and always remains on "Hardware" after application restart.
- Solved:" Select layer" action does not work with native file types (.sgsj, .sgpj, .sglj).
- Solved: "An unexpected error occurred" when cutting print&cut jobs containing vertical lines with "Fixed size (smart compensation)".
- Solved: "Marks are too far apart in X direction" error can occur randomly when trying to output a print&cut file.
- Solved: Using the"Restore" function to restore action sets with an XML file that does not match the expected XML results in an empty action set being "restored".
- Solved: GoProduce LE license is not activated for all users on a pc but only for the active user.
- Solved: Properties that use the DoubleUpDown control will incorrectly display a red border indicating that the value is exceeding the limit even when it's still an acceptable value when using "inch" or "cm" as unit.
- Solved: too long prefeed in some cases because of using X and Z axes with vision calibration.
- Solved: Shift between segments with "Fixed size" compensation because of using X and Z axes with vision calibration.
- Solved: Creating zip archive on "Feed and roll scan" can take too long if the previous job was very long.
Summa GoProduce Laser Edition - Version 2.1.0
Released: March 2, 2023
New Features
- Export to PDF (PRO PACK).
- Page select on import for multipage PDF documents.
- Added USB driver vision camera to installer.
- Added “Trace and Cut.pdf” sample file.
Improvements
- Support segment connector for Trace & Cut.
- Minimum allowed value for segment connector of 0.1 mm.
- Support CCT format for serial numbers.
- Add application settings .xml files under ProgramData in order to zip backup archive, created on "Load" action for better troubleshooting.
- Sample file to setup the power to cut a material.
- Rename "Zund" and "Esko" titles to "ZCC" and "i-CUT".
- Changed minimum width and length for "Plot to file" to 100 mm, changed maximum and default width and length to 50 m.
- Different error message than “Predicted mark lies outside of media area" when barcode detection tries to move outside the media area.
- Slightly improved mark prediction to solve inaccuracies with jobs having a "bowing" effect.
Fixed Issues
- Solved: In some cases, GoProduce LE can crash when entering the serial number during activation.
- Solved: Opening a .sgsj file will still show the previous file name as job title instead of the actual .sgsj file name.
- Solved: When executing a print & cut job, "Apply" mark can be available even though there's no mark detected.
- Solved: Mark detection can get stuck, jumping endlessly from one position to another.
- Solved: Saving PDF file as a .sglj file while the property "Separate layers for PDF" is set to "by color" and re-opening the newly saved .sglj file would result in invisible lines.
Summa GoProduce Laser Edition - Version 2.0.1
Released: January 3, 2023
Changes to 2.0.1
Improvements
- Support multiple activation licenses for production.
- Increased max value of margin of clean-up actions (Reduce nodes, Remove double lines/objects, Break at intersections, Close objects) to 3 mm (3/32 in).
- Trace&Cut: faster tracing by skipping seed points that would have the same result as seed points that were already used. Skipped seed points are shown in a different colour.
- "Colour bar" option in "Trace" action to cope with long printed colour bars at the sides of the job.
- For Trace&Cut, seed left and right on the first segment to cope with colour bar printed at one side of the material.
- Changed default park distance to 750 mm (29,53 in) in "Load Material" action and default action set "Feed and roll scan".
Fixed issues
- Solved: Zund and Esko options are not hidden in the Import Job action properties window when Pro Pack is not activated.
- Solved: "Close objects" action sometimes chooses the wrong objects to close, for example in a raster of rectangles.
- Solved: Wrong regmark size when importing Esko files which are defined inches.
- Solved: GoProduce LE 2.0.0 can crash on activation because of missing QrCoder.dll in installation folder.
- Solved: During Trace&Cut, only cancels after "Tracing" step when cancel was pressed when "Filtering" was busy, which might cause a long time before the process is cancelled.
- Solved: For Trace&Cut, sometimes unwanted horizontal lines are generated at the bottom of a scan that doesn't cover the complete working area.
- Solved: Waste cut cutting through shapes on the first segment of a trace&cut job.
- Solved: Wrong (circle) regmark position when importing ZCC or CUT file.